Saturday,26-August-2017
Fiat Punto : valve cover seal replacement
EN
That is pretty straight forward, and easy task and the pictures are just small guide.
You need 10mm socket and maybe no more than 15min to do that. Good luck 
Ford Tourneo: Car sound update
EN
Good day,
Have you ever thought about improving the sound in cargo van? Me neither to be exact, but here is it. Mate of mine ask if we can do something fast. Well, improvement was: SUB woofer with AMP, new stereo, speakers and few hours lost.
Saturday, 5-August-2017
Xsara Mk I - dashboard bulb replacement
EN
Here is short tutorial how to replace dash bulbs on Xsara MK I.
Pull the central vents first. Be careful when pulling the plastic frame around dash and vents. The cabin temperature sensor fan can be pulled easy but hazard lights switch plug can be stubborn.
Hyundai Getz - handbrake lamp problem fix
| EN | BG |
| And here we go. The problem in that case was: doesn`t matter up or down the handbrake on the dash, the info lamp was ON all the time. Seems ground to it was constant. | Проблемът тук бе в постоянно светеща лампа на ръчната спирачка.Без значение отпусната или не. И според мен бе - константна маса до лампата по някаква причина. |
Sunday, 4-June-2017
Passat 3B2 - messing with wires :)
EN
That time mate of mine call me to check over his car if we can find some solution about missing power to door welcome lights.
It seem that all positive voltage supply to door and cabin map lams are taken from comfort module, and ground taken either from door lock unit or control pin from the same comfort module.
[Read More…]
Sunday,28-May-2017
Xantia Estate Trunk Cover plastic ends/hooks [FIX]
EN
Hi there,
If you own Xantia Estate perhaps some day you`ll get to the point where that damn plastic ends just break.
Well, option one is to pay 54e for pair and get from Citroen dealer if you still can, or …. 3D print them.
I spend quite some time measuring, CAD modelling and 3D print test, so finally can say have something useful:
Monday, 1-May-2017
Add dual fan system to 2.5W cnc laser
EN
Hello reader,
In that article wish to show and share one idea of mine for dual fan system (biturbo ha ha) for my cnc 2.5W laser. That is suitable with probably all hobby laser coolers using 30mm fans and aluminium profile 33×33 mm for cooling. So here we go:
[Read More…]
Saturday,22-April-2017
Woodpecker GRBL CNC Board - Firmware Update
EN
If you own CNC 2418 machine(like me), or just have Woodpecker GRBL CNC Board you can update to GRBL firmware v1.1.
But if you`re “lucky” like me,when try via Arduino IDE, you`ll hit into: “resp. = 0×0d” or similar compiler error. That is because the Atmel chip is without boot loader. Even with Xloader you`ll hit the wall. So then what?
[Read More…]
Friday,14-April-2017
Jetta 1K2 - immo problem [solved]
EN
Have to admit - sometimes VW make really good puzzles for solving with their documents. This time the car that will talk about is Jetta model 2006. 1.6 FSI with average equipment.
The problem was that after visit to service the car suddenly lost central lock. Dealer conclusion was: you need new set of keys and front doors lock motors replaced. Well…
[Read More…]
Lenovo K910 power cable fix
EN
Lenovo K910 - not that bad phone, but the owner of that Chinese marvel grumble that in few days it did charge only from time to time, and when move the power supply cable sometimes it work sometimes not.
From ebay was ordered new ribbon cable and here how it goes..
[Read More…]
